Soap Tube and Brush Shaving Kit Case- Personalized - 3D Printed

$35.00
Soap and Brush Case:
• The case comes with an Soap Dispenser Tube Compatible with Arko soap and one free Soap
• Comes with my Custom Shave Brush and Brush Tube
• You can also load scoops of your favorite soap in the Soap Tube
• Cap end has holes for air flow to keep brush and soap dry
•Cap is held in place by magnet latches
• Plastic Filaments MADE IN THE USA in TEXAS!
• Dishwasher Safe PETG Plastic, PLA is not dishwasher safe due to the heat
• High Quality, Tough and UV Resistant

Personalization Note: To guarantee your custom text perfectly pops against all 17 of our color options, text and logos are exclusively available in High-Contrast Black or High-Contrast White

Shave Brush:
• 34mm wide x 31.6mm tall base
• 22mm Tuxedo bulb shaped black synthetic knot with 50mm loft
• Great backbone with super soft white tips
• Handle is light weight and very comfortable in the fingertips

Arko Shave Stick with shave stick holder tube:
► Softens your beard for a close and extra comfortable shave
► Protects skin from shaving irritations
► Leaves skin feeling clean and comfortable
► Stick fits in custom holder tube
► To Use: 1- Push soap up 1/4" to 1/2" out the top, press sides of tube to hold soap in place. 2- Wash face with hot water. 3- Apply hot water to face with hands, massaging in. 4- Wet the end of the soap stick with hot water and rub over face, repeat until face is lightly coated. 5- Rinse brush with hot water and lightly shake out excess. 6- Swirl brush over face vigorously to whip up a nice lather. 6- Add more water to the brush or soap to the face as needed to get a full lather. There are lots of instructional videos of using the Arko Shave Soap on Youtube.

Arko Soap Setup: Arko soap out of the box is rarely completely round. Take the soap and roll it on a counter with the palm of your hand until it is round enough to fit in the tube. Place the barbed disk in the bottom of the tube, insert the soap, and put the Plunger in the end of the tube. Press down on the plunger to seat the soap on the barbed disk and mold the soap to the form of the tube. Press up on disk from bottom and peel 1/4" to 1/2" of paper off soap and you are ready!

If the Arko Stick paper cover starts to deteriorate and stick, run tube under hot water to loosen and remove. Take off all original paper and cover with 1 layer of tin foil. This will help it to slide up and down alot easier and get rid of sticking.

The Shave Brush and Case is Made In The USA and is Copyright 2025 - Chris M Spencer. CAD Designed and 3D printed by me in Marble PETG Filament. As with all 3D prints, some layer lines may show more than others.
Case Color:
Text Color:
Soap and Brush Case:
• The case comes with an Soap Dispenser Tube Compatible with Arko soap and one free Soap
• Comes with my Custom Shave Brush and Brush Tube
• You can also load scoops of your favorite soap in the Soap Tube
• Cap end has holes for air flow to keep brush and soap dry
•Cap is held in place by magnet latches
• Plastic Filaments MADE IN THE USA in TEXAS!
• Dishwasher Safe PETG Plastic, PLA is not dishwasher safe due to the heat
• High Quality, Tough and UV Resistant

Personalization Note: To guarantee your custom text perfectly pops against all 17 of our color options, text and logos are exclusively available in High-Contrast Black or High-Contrast White

Shave Brush:
• 34mm wide x 31.6mm tall base
• 22mm Tuxedo bulb shaped black synthetic knot with 50mm loft
• Great backbone with super soft white tips
• Handle is light weight and very comfortable in the fingertips

Arko Shave Stick with shave stick holder tube:
► Softens your beard for a close and extra comfortable shave
► Protects skin from shaving irritations
► Leaves skin feeling clean and comfortable
► Stick fits in custom holder tube
► To Use: 1- Push soap up 1/4" to 1/2" out the top, press sides of tube to hold soap in place. 2- Wash face with hot water. 3- Apply hot water to face with hands, massaging in. 4- Wet the end of the soap stick with hot water and rub over face, repeat until face is lightly coated. 5- Rinse brush with hot water and lightly shake out excess. 6- Swirl brush over face vigorously to whip up a nice lather. 6- Add more water to the brush or soap to the face as needed to get a full lather. There are lots of instructional videos of using the Arko Shave Soap on Youtube.

Arko Soap Setup: Arko soap out of the box is rarely completely round. Take the soap and roll it on a counter with the palm of your hand until it is round enough to fit in the tube. Place the barbed disk in the bottom of the tube, insert the soap, and put the Plunger in the end of the tube. Press down on the plunger to seat the soap on the barbed disk and mold the soap to the form of the tube. Press up on disk from bottom and peel 1/4" to 1/2" of paper off soap and you are ready!

If the Arko Stick paper cover starts to deteriorate and stick, run tube under hot water to loosen and remove. Take off all original paper and cover with 1 layer of tin foil. This will help it to slide up and down alot easier and get rid of sticking.

The Shave Brush and Case is Made In The USA and is Copyright 2025 - Chris M Spencer. CAD Designed and 3D printed by me in Marble PETG Filament. As with all 3D prints, some layer lines may show more than others.